Bbk-performance 1608 User Manual download pdf

‘96-04 V-8 Mustang Pulley Set

Part #’s 1564 & 1608

INS-105

INSTALLATION INSTRUCTIONS

www.BBKPERFORMANCE.com

IMPORTANT—All appropriate safety equipment (e.i., gloves, tools) must be used during the installation of this product(s).

BBK Performance, Inc. accepts no responsibility for injuries resulting in the installation of any product(s).

Included in this kit: Alternator pulley, water pump pulley, crank balancer, and installation bolt.

ATTENTION !

This installation requires the use of an impact wrench and a balancer puller tool.

Step 1 Visually identify which pulley/pump you have using the included info sheet.

Step 2 Loosen the alternator pulley nut with an impact wrench.

Step 3 Loosen the four water pump pulley bolts.

Step 4 Remove the serpentine belt by inserting the head of a 1/2” ratchet into the square hole in the belt tensioner and

pushing down (rotating it clock-wise) then pulling the belt off of one of the pulleys.

Step 5 Remove the water pump pulley.

Step 6 Remove the crank bolt using an impact wrench (if your impact wrench is too big you may need to remove the

radiator fan to access the bolt straight on.

Step 7 Remove the washer from the bolt and finger tighten the bolt back into the crank snout.

Step 8 The stock balancer will either have three perches cast into it for a 3 prong puller tool, or 3 threaded bolt holes to

facilitate the use of a flat (plate style) puller tool. Attach the puller tool to the balancer and use the head of the

stock crank bolt as a pressure point for the puller tool. Tighten the drive bolt on the puller tool until the balancer

comes off of the crank snout completely.

Step 9 Inspect crank snout to ensure there are no burrs or rust, if required polish with very fine emery paper or steel

wool, wash clean.

Step 10 Apply a light bead of black RTV to the keyway of the BBK damper then locate the balancer onto the crankshaft

lining up the crank snout key into the key-way slot in the balancer.

Step 11 Place the supplied M-12 x 60mm bolt through the original washer and tighten it to pull the balancer onto the

crank snout until the stock bolt can reach. DO NOT TIGHTEN THE SUPPLIED BOLT ALL THE WAY! IT IS ONLY

THERE TO PULL THE BALANCER ONTO THE CRANK SNOUT UNTIL THE ORIGINAL BOLT CAN REACH.

Once the original bolt can be threaded in safely, remove the supplied bolt and place the original bolt through the

original washer and tighten it until the balancer is fully engaged on the crank snout.

Step 12 Follow the Ford torque specs to complete the balancer installation.

On automatic transmission cars, you may need to keep the engine from turning while tightening the balancer by

removing the inspection cover on the front driver side of the transmission and holding the torque converter with

a 14mm wrench.

Step 1. Torque to 66 lb-ft

Step 2. Loosen bolt 1 full turn

Step 3. Torque to 37 lb-ft

Step 4. Tighten bolt an additional 90°

1 2 3

Summary of Contents

Page 1 - Part #’s 1564 & 1608

‘96-04 V-8 Mustang Pulley SetPart #’s 1564 & 1608INS-105INSTALLATION INSTRUCTIONSwww.BBKPERFORMANCE.comIMPORTANT—All appropriate safety equipment

Page 2 - Completed installation

Step 13 Install the BBK water pump pulley using the original bolts.Step 14 Install the BBK alternator pulley using the appropriate one of the two supp

Page 3

Identification Guide for 4.6L Water Pump PulleysVisually identify which water pump pulley you have before installing regardless of model year. The ear

Related models: 1564

Comments to this Manuals

No comments

Bbk-performance 1608 User Manual

Browse online or download User Manual for For the car Bbk-performance 1608. BBK Performance 1608 User Manual

Summary of Contents

Related models: 1564

Comments to this Manuals

Related products and manuals for For the car Bbk-performance 1608